Briggs & Stratton Racing Community Forums

"So I just purchased the Lo206 and installed it this weekend. Package came with a black slide, but I had to change it to the red since we are going …"

Posted in Animal/206 Engine Questions by agepag

"We switched to the 206 from the comer a little over a month ago (thank god). At first it poured gas out the carb. Adjusted the float and it ran …"

Posted in Animal/206 Engine Questions by pole44

"This rod is pulled from running engine with 14 hours after rebuilt (not sure if the rod was replaced though). The crank journal looks decent. When …"

Posted in M Series/World Formula Questions by Genes1s

Loosing oil lo206

New to me kart.. No leaks went about 3 hours between oil change and I'm getting oil out of the fuel pump. Cart runs fine. Had 8 ounces in it. Category: Animal/206 Engine Questions

View Post »

inboard or outboard

I know clutch installation is very important and have watched the vidio a few times. But there is nothing about inboard or outboard mounting in the vidio or on the forum. I need to mount the clutch …

View Post »

Fuel not reaching pump from fuel tank

Hey guys, when pulling the engine cord on my 206, the fuel in the fuel line moves closer to the pump but never fully reaches it, even after pulling the cord for 5 straight minutes. I fixed this by …

View Post »

Flywheel Fan

Mine turned into pieces and I'm wondering what caused the flywheel fan to shatter?The 2 bolts are still tight and holding the last bit of the remnants. Kart wasn't overheating or anything. Category: …

View Post »

0 deg. Motor mount on LO 206 motor

Do you recommend flat mounts on the 206 motors and if so would the minimum oil level need to be increased? Category: M Series/World Formula Questions

View Post »

Engine seals

Our club has started a 206 program.Would removing one or both of the factory seals and replacing with NUMBERED club race seals void any kind of factory warranty program?Bear in mind that our club is …

View Post »

lo206 junior stumbling and not reaching max rpm

We switched to the 206 from the comer a little over a month ago (thank god). At first it poured gas out the carb. Adjusted the float and it ran beautifully! Then we had an issue with it not reaching …

View Post »

WF Connecting rod failure modes and re-usability.

This rod is pulled from running engine with 14 hours after rebuilt (not sure if the rod was replaced though). The crank journal looks decent. When one looks at the connecting rod, what do you call …

View Post »

lo206 carb issues seems rich please help.

new lo206 engine just broke in and on gas. question if its tuned right. Seems rich. When warmed up aand hit throttle it blows black smoke. just for fun kart. Have read and watch briggs informal …

View Post »

ARC Momgrel Clutch

Is the ARC Mongrel clutch legal for L206 or would it be considered a modified Max-Torque. It's for the L206 Masters or Heavy.Ben Category: Animal/206 Engine Questions

View Post »

JR dragster

Not getting power out of the lo206. Supposed to run a 13.90 or slower and ran a 34.60 first time down the track. Checked the blue slide in carb and cannot get it to open the allowed limit. Needs to …

View Post »

Model 49 parts interchange racing parts

I wrote this message to Briggs, Guys, I am working with a Model 49T877-0004-G1 Serial 14 0123 YG 38082, engine. Model 49 I presume is the short term for it. Having a hard time finding racing parts, …

View Post »

Intek and Professional models, are they the same?

Does the Briggs Professional model 27 h.p. engine use the same flywheel and internal parts as the Briggs Intek model 27 h.p. engine? If there are differences, what are they? Category: …

View Post »